[IBC] Lime Sulfur
I have a malphigia growing over a piece of driftwood. The wood seems to be
softening somewhat. I had treated it with wood hardener before using it. Can I apply lime sulfur without harming the malphigia? Carol in S. Florida - Zone 10 ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
Penetrating epoxy will repair really rotted wood.
I have used one that is very watery and has a cure time of several hours. The procedure is to brush it on, wait for it to soak in, then repeat endlessly, until it stops soaking in. The epoxy penetrates more on really rotted wood, less on solid wood. The treated wood will be darker & have a sheen, but after a bit of time & one or more treatments with lime sulphur, it will be very difficult if not impossible to detect. It may need more epoxy in a few years. I have treated the interior of an apple that was so rotted you could carve it with your fingernails (it needed more epoxy in a few years) and a priceless collected juniper that had crumbling shari. Both are doing fine. For me, the question that remains is, what will these trees be like in 10 - 20 - 50 years? Will they rot out under all the epoxy (or wood hardener) & shed the plasticized wood? I bought mine from a Richmond, CA manufacturer, but I think penetrating epoxy is available at Home Depot & at boat shops for repairing rotted wood. Jim Gremel On Sep 1, 2005, at 6:22 PM, Billy M. Rhodes wrote: In a message dated 9/1/2005 9:15:51 PM Eastern Standard Time, writes: I have a malphigia growing over a piece of driftwood. The wood seems to be softening somewhat. I had treated it with wood hardener before using it. Can I apply lime sulfur without harming the malphigia? Carol in S. Florida - Zone 10 I am not sure I understand. Your plant has dead wood that you painted with wood hardener? Now it is getting soft? The lime sulfur will not help, but more wood hardener might. Or is it the driftwood that is getting soft. Then more wood hardener s what you want. I put some Min Wax Wood Hardener on a Bougainvillea it must have adsorbed six coats. Wood hardener will not repair really rotten wood, you must remove the rotted wood and apply the product to good wood to prevent further rot. Billy ************************************************** ********************* ********* ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ********************* ********* -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
Penetrating epoxy will repair really rotted wood.
When you epoxy (or harden) already rotted wood, without removing all of the rot, you are asking for more rot. None of these -- epoxy or wood hardener -- soaks into _all_ of the rotted area. Any rot left behind deep in the tree will grow. It's also somewhat questionable whether these things actually kill the rot fungi. Treatment by either of these should be attempted only after you have scraped and cut away to bare, hard wood and then a little more, if possible. Even then, since the fungal spores that cause the rot are _so_ small, you likely will leave some behind. (Perhaps a bath in some kind of fungicide before the hardening treatment would help, but . . .) Of course, the rot itself won't kill a tree. The decay fungi and bacteria don't attack living wood, just the interior deadwood -- which the tree is always making, so there's an endless and growing supply. In nature, death comes because the rot has taken away so much of the hard tissue that holds a tree upright that it becomes top heavy and snaps off (usually onto someone's roof, it seems). In bonsai, a bad case of rot simply has to be designed into the tree. Fillers and other things used to restore the original outline again adhere to the wood uncertainly, and the inevitable spaces become the sites of future, eventual rotting. It's usually better to cut it all away and then see what you can make of what you have left. Jim Lewis - - Tallahassee, FL - Nature encourages no looseness, pardons no errors. Ralph Waldo Emerson ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
----- Original Message -----
From: Subject: [IBC] Lime Sulfur I have a malphigia growing over a piece of driftwood. The wood seems to be softening somewhat. I had treated it with wood hardener before using it. Can I apply lime sulfur without harming the malphigia? Carol in S. Florida - Zone 10 A helpful hint, once you get rid of most of the "pulpy" rot and then treat the rest with MinWax woodhardener , you'l find that Lime Sulfur easily and quickly washes off that slippery finish. If you treat the wood BEFORE applying MWH , and adjust it to coloration you want, THEN apply MWH it will "Lock In" the color and won't wash off. Note, the Lime Sulfur will ONLY be for contrast/effect on this wood. It won't stop rot or bugs. Regards, Dale ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
A big thank you for all of you who gave me great information regarding the
use of lime sulfur. I learned lots and am busy putting all the info into practice. Carol in S. Florida - Zone 10 ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
Carol, I'm also in Forida.
What you have done is known as a Phoenix graft, attaching a small slender tree to an interesting piece of driftwood. The main reason for rot on the driftwood is fungi because of the constant humidity from watering your tree daily. Then after fungi sets bacteria may also start working. Lime sulfur actually play a key role in your case. Lime sulfur is one of the least toxic, most effective controls for peach leaf curl, brown rot, and other fungus problems. Also used for control of pear blister mite, caneblight and scab. For this it should be diluted at 4 Tbs-1 cup/gal of water. Lime sulfur was first used on bonsai for that purpose, but then someone realized that applying directly the concentrate on the deadwood not only prevented fungus problems for up to 6 months, but have a desiderable unexpected side effect: it bleached the wood as it has been exposed to the elements (weathered) in nature for years. Using the lime sulfur concentrate (non diluted) will certainly get rid of all fungus/rot problems and keep the driftwood bleached. In my humble opinion thats all you need. I dont think wood hardener will be neccesary in the future if you apply lime sulfur regularly, say quarterly. When you do use a small brush or artist brush if neccesary to avoid excessive lime sulfur on the live tree bark and foliage. Cover also the surface of the soil with some plastic (groceries plastic bags from your local supermarket) to avoid excessive dripping of the lime sulfur concentrate to the roots of your tree. Hope this help you answer the question. Gene Quote:
|
On Sep 13, 2005, at 5:38 AM, Isom, Jeff ((EM, PTL)) wrote:
Do you happen to have a brand (or product) name for this? I have a collected Arborvitae that needs it! Thanks, Jeff Isom I bought my epoxy from the manufacturer: Smith & Co. in Richmond, CA, (510) 237-6842. Their product is called Clear Penetrating Epoxy Sealer. The label states: “This extremely effective sealer is used in the treatment of dry rot in wood, the sealing of concrete, and as a consolidant for porous materials. It can ensure adhesion of a wide variety of varnishes, paints, adhesives and caulkings. It consists of a tough, flexible epoxy resin system in a solvent blend which dissolves the natural saps, oils and moisture of wood and develops a chemical bond with the wood fibers themselves... .... Pot life of the regular formula is 8 hours at 72 deg. F, with full chemical cure in 7 days at 72 deg. F. Pot life of the fast formula is 2 hours at 72 deg. F, with full chemical cure in 2 days at 72 deg. F.” As of 9/13/05, their price for a 2 quart kit is about $39. + tax. The have 2 pint kits & 2 gallon kits as well. It is made in a 2 hour cure version & an 8 hour cure version. Either would be fine for bonsai. Smith & Co. will ship, but they recommend checking with their distributor at www.star-distributing.com - Star takes credit cards, has an online store and also has retail outlets in some East Coast cities. I have seen penetrating epoxy is at Home Depot & I am expect that it is available at boat shops everywhere at boat shops - a Google search for “penetrating epoxy” gave 860 references. Jim ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
Jim: Have you already used it? (I did not see the earlier part of this thread?) If not, I would be certain that this does not seep through wood into live tissue. Experimentation might be the way to go . . . with less than precious material. The word "penetrating" concerns me. Cordially, Michael Persiano members.aol.com/iasnob -----Original Message----- From: Jim Gremel To: Sent: Tue, 13 Sep 2005 11:01:26 -0700 Subject: [IBC] Lime Sulfur On Sep 13, 2005, at 5:38 AM, Isom, Jeff ((EM, PTL)) wrote: Do you happen to have a brand (or product) name for this? I have a collected Arborvitae that needs it! Thanks, Jeff Isom I bought my epoxy from the manufacturer: Smith & Co. in Richmond, CA, (510) 237-6842. Their product is called Clear Penetrating Epoxy Sealer. The label states: "This extremely effective sealer is used in the treatment of dry rot in wood, the sealing of concrete, and as a consolidant for porous materials. It can ensure adhesion of a wide variety of varnishes, paints, adhesives and caulkings. It consists of a tough, flexible epoxy resin system in a solvent blend which dissolves the natural saps, oils and moisture of wood and develops a chemical bond with the wood fibers themselves... .... Pot life of the regular formula is 8 hours at 72 deg. F, with full chemical cure in 7 days at 72 deg. F. Pot life of the fast formula is 2 hours at 72 deg. F, with full chemical cure in 2 days at 72 deg. F." As of 9/13/05, their price for a 2 quart kit is about $39. + tax. The have 2 pint kits & 2 gallon kits as well. It is made in a 2 hour cure version & an 8 hour cure version. Either would be fine for bonsai. Smith & Co. will ship, but they recommend checking with their distributor at www.star-distributing.com - Star takes credit cards, has an online store and also has retail outlets in some East Coast cities. I have seen penetrating epoxy is at Home Depot & I am expect that it is available at boat shops everywhere at boat shops - a Google search for "penetrating epoxy" gave 860 references. Jim ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
Well, yes, "penetrating" can be a provocative word...
I have used it, with great concern about what it would do to the live tissue. The first tree was an apple that had a naturally rotted & hollowed trunk. Gorgeous base, but the wood was rotted enough that I could carve it with my fingers. The tree is doing fine, but I gave it more epoxy a few years later, when it seemed that the rotted wood was again, or still, porous. I have also used it on two very precious collected junipers with excellent results (earlier I said one juniper, but I now remember a second one). Perhaps the epoxy would damage live tissue, but just didn't get that far. I have soaked dry but unrotted juniper sticks in the epoxy. After curing, I cut them to find the penetration was minimal. On my junipers, the epoxy firmed up weak & porous wood that wouldn't have lasted much longer without it. As I said earlier in this thread: For me, the question that remains is, what will these trees be like in 10 - 20 - 50 years? Will they rot out under all the epoxy (or other wood hardener) & shed the plasticized wood? There are uncertainties, but it seems to be my best option for some trees. jim On Sep 13, 2005, at 1:28 PM, wrote: * * Jim:* Have you already used it?* (I did not see the earlier part of this thread?)* If not, I would be certain that this does not seep through wood into live tissue.* Experimentation might be the way to go . . . with less than precious material. * The word "penetrating"*concerns me. * Cordially, * Michael Persiano members.aol.com/iasnob* * -----Original Message----- From: Jim Gremel To: Sent: Tue, 13 Sep 2005 11:01:26 -0700 Subject: [IBC] Lime Sulfur On Sep 13, 2005, at 5:38 AM, Isom, Jeff ((EM, PTL)) wrote:* * Do you happen to have a brand (or product) name for this? I have a* collected Arborvitae that needs it!* * Thanks,* * Jeff Isom* * I bought my epoxy from the manufacturer: Smith & Co. in Richmond, CA, (510) 237-6842.* * Their product is called Clear Penetrating Epoxy Sealer. The label states:* * "This extremely effective sealer is used in the treatment of dry rot in wood, the sealing of concrete, and as a consolidant for porous materials.* * It can ensure adhesion of a wide variety of varnishes, paints, adhesives and caulkings.* * It consists of a tough, flexible epoxy resin system in a solvent blend which dissolves the natural saps, oils and moisture of wood and develops a chemical bond with the wood fibers themselves...* * ... Pot life of the regular formula is 8 hours at 72 deg. F, with full chemical cure in 7 days at 72 deg. F.* * Pot life of the fast formula is 2 hours at 72 deg. F, with full chemical cure in 2 days at 72 deg. F."* * As of 9/13/05, their price for a 2 quart kit is about $39. + tax. The have 2 pint kits & 2 gallon kits as well. It is made in a 2 hour cure version & an 8 hour cure version. Either would be fine for bonsai.* * Smith & Co. will ship, but they recommend checking with their distributor at www.star-distributing.com - Star takes credit cards, has an online store and also has retail outlets in some East Coast cities.* * I have seen penetrating epoxy is at Home Depot & I am expect that it is available at boat shops everywhere at boat shops - a Google search for "penetrating epoxy" gave 860 references.* * Jim* ************************************************** ********************* ********** * ++++Sponsored, in part, by Bob Pastorio++++* ************************************************** ********************* ********** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ --* * +++++ Questions? Help? e-mail +++++* ************************************************** ****************************** ++++Sponsored, in part, by Bob Pastorio++++ ************************************************** ****************************** -- The IBC HOME PAGE & FAQ: http://www.internetbonsaiclub.org/ -- +++++ Questions? Help? e-mail +++++ |
All times are GMT +1. The time now is 11:40 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
GardenBanter