Allen shredder & similar users help
 

Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat.
Is this normal, have I a problem, or is there a way to stop it? TIA

Allen shredder & similar users help
 

"Broadback" wrote in message
...
Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat. Is
this normal, have I a problem, or is there a way to stop it? TIA

Mine's an AL-Ko, and when it does that it's getting blocked up.

Steve

Allen shredder & similar users help
 

On Tue, 31 Jul 2007 10:17:56 +0100, Broadback wrote:

Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat.
Is this normal, have I a problem, or is there a way to stop it? TIA

I've had an Allen for many years. It does sometimes do what you say but
only when the bag is getting too full or (as Shazzbat says) when it's
getting blocked. The Allen took a little getting used to but since I did,
it's been great :-)

HTH.
--
Regards,

Hugh Jampton

Allen shredder & similar users help
 

Hugh Jampton wrote:
On Tue, 31 Jul 2007 10:17:56 +0100, Broadback wrote:

Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat.
Is this normal, have I a problem, or is there a way to stop it? TIA

I've had an Allen for many years. It does sometimes do what you say but
only when the bag is getting too full or (as Shazzbat says) when it's
getting blocked. The Allen took a little getting used to but since I did,
it's been great :-)

HTH.
Thanks Folk, that was the problem. Now the problem is that it keeps
blocking, I even had to completely strip down to the blades at one
point. I am shredding hedge cuttings, feeding them into the hopper. It
eats them up no trouble, but starts to get blocked before the bag is 1/2
full, this at least necessitates taking off the discharge cover in order
to remove the screen and clean. Now as everyone says how good they are I
accept that I am doing something wrong, any ideas please? At the moment
it is taking me almost as long as with my electric shredder, as that
rarely blocks, if it does it take very little time to clear.

Allen shredder & similar users help
 

"Broadback" wrote in message
...
Hugh Jampton wrote:
On Tue, 31 Jul 2007 10:17:56 +0100, Broadback wrote:

Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat.
Is this normal, have I a problem, or is there a way to stop it? TIA

I've had an Allen for many years. It does sometimes do what you say but
only when the bag is getting too full or (as Shazzbat says) when it's
getting blocked. The Allen took a little getting used to but since I did,
it's been great :-)

HTH.
Thanks Folk, that was the problem. Now the problem is that it keeps
blocking, I even had to completely strip down to the blades at one point.
I am shredding hedge cuttings, feeding them into the hopper. It eats them
up no trouble, but starts to get blocked before the bag is 1/2 full, this
at least necessitates taking off the discharge cover in order to remove
the screen and clean. Now as everyone says how good they are I accept that
I am doing something wrong, any ideas please? At the moment it is taking
me almost as long as with my electric shredder, as that rarely blocks, if
it does it take very little time to clear.

The blockage IME is due to the material being shredded being damp. Can you
dry it off a bit in the sun (now we've got some) for a couple of days before
shredding?

Steve

Allen shredder & similar users help
 

On Tue, 31 Jul 2007 16:55:36 +0100, Broadback wrote:

Thanks Folk, that was the problem. Now the problem is that it keeps
blocking, I even had to completely strip down to the blades at one
point. I am shredding hedge cuttings, feeding them into the hopper. It
eats them up no trouble, but starts to get blocked before the bag is 1/2
full, this at least necessitates taking off the discharge cover in order
to remove the screen and clean. Now as everyone says how good they are I
accept that I am doing something wrong, any ideas please? At the moment
it is taking me almost as long as with my electric shredder, as that
rarely blocks, if it does it take very little time to clear.

Shazzbat suggests it's wet stuff causing the problem. My Allen copes with
wet(ish) hawthorn/privet and similar *but* I well remember the day I tried
to shred new potato stalks and leaves just after digging - blocked the
shredder totally - had to take it to bits to clear it :-(

Is it getting blocked on the entrance or discharge ? If on discharge then I
think it's probably caused by wet - but if your electric shredder copes
with that kind of stuff then I find it odd. If on entrance then mine does
that occasionally - it's the way you feed it :-)

Sorry you're having problems - I really would be lost without my Allen and
hope you get sorted soon - please keep us informed.
--
Regards,

Hugh Jampton

Allen shredder & similar users help
 

On Tue, 31 Jul 2007 16:55:36 +0100, Broadback
wrote:
I accept that I am doing something wrong, any ideas please?

Perhaps you arnt doing anything wrong, it could be that we have not
encountered your type of hedge/conditions ! :-!))
Well, gotta blame it on something, it isnt computer driven, so blaming
that is out ;)
but I can imagine you are somewhat disheartened after spending all
that dosh :(

The only idea I have at the mo.
( in addition to what has been said by the others, like whom I am a
bit mystified cos I've had no troubles like this, else I wouldnt have
been one of the ones recommending it, as you can imagine !)
is to wonder if the hammers are all free to move on their pivots ?

The blades at the front, insideof the chute, are just the first
stage(PS*), then there is a set of pivoted hammers that should mangle
(masticate ! ) the bits before squidging them through the output gate.

Is is a new machine or s/hand ? If the former then the tolerances on
manufacture are (were) a bit tight, two of my (9?, its a long time
since I took it apart) hammers (flails) were not free to move
initially.
If s/h then perhaps they have rusted up ?

The rest is just witterings in the hope that something will emerge :--

What type of hedge ? I use mine on private ( large leaf stuff) and on
that horrid wee leaved thing that some call private but is something
else I think and laurel formal hedgings, but rather more copious
quantities of general shrubs, undergrowth, brambles, tree prunings
etc.
all go through without problems.

Are your hedge trimmings all really wet leafy green stuff or does it
include lots of the wee twiggy bits ?

If it is all wet leafy green stuff, have you got other twiggy/woody
stuff to include with it ?
Or even a few branches to shove down the chipper shut to clear the
clog ?

I agree that potato haulm could well clog it up, but I have copious
quantities of autumn fall wet beech leaves to sweep up onto it,
or vacuum up with the rotary mower and tip into it ( Im impatient and
want my leafmold heaps to break down quick !) No prob.

Im out of ideas, I'll have another ginger wine to see if that tells me
anything !

(*PS) else it would produce stuff just like a flymo

Allen shredder & similar users help
 

PPS
This is what I do to check my hammers/flails
I am not suggesting that anyone else does this

remove spark plug cap, and if really really wimpish, back of the spark
plug to remove compression,,,,

reach down the chute and push/shove/rotate the blades incrementally
till, wth the other hand, feel, up through the outet shield, the
hammers enter the output grill, check that each is free to move.
some may be a bit stiff to your fingers, but centrifugals when under
power will be no bother to them !

Allen shredder & similar users help
 

On Tue, 31 Jul 2007 10:17:56 +0100, Broadback
wrote:
Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat.
Is this normal, have I a problem, or is there a way to stop it? TIA

Have you got it sorted ?

Allen shredder & similar users help
 

WaltA wrote:
On Tue, 31 Jul 2007 10:17:56 +0100, Broadback
wrote:
Following recommendations here I have purchased the above shredder. A
question or 2 please from users. It shreds easily and quickly, however
when shredding hedge cuttings through the large hopper I get quite a lot
of very fine shreddings (almost dust)blowing out of the chipper throat.
Is this normal, have I a problem, or is there a way to stop it? TIA

Have you got it sorted ?

Having been away for a couple of days I have not yet tried all the
recommendation's, for which I thank you. I am shredding cuttings from
holly, beech and mainly hawthorn. The problem was worse when I threw
some broad been stalks in, I learnt that lesson. As regards the hammers
mentioned I can see none of those in my shredder. There is a disk which
has cutters on, on the reverse side is a cutter to deal with bigger
sticks. Incidentally feeding sticks in is a bit of a problem, as they
are not drawn in but need feeding all the way, which of course is not
possible, without finger risk. Finally there is a metal bar, about 4cm
wide, 25cm long with a hole at one end and chamfered at the other, what
is that for please?

Allen shredder & similar users help
 

On Fri, 03 Aug 2007 18:23:33 +0100, Broadback wrote:
WaltA wrote:
Have you got it sorted ?

Having been away for a couple of days

Phew, that's a relief, I thought for a mo. you might have thrown it
off a high cliff in frustration !

I have not yet tried all the
recommendation's, for which I thank you. I am shredding cuttings from
holly, beech and mainly hawthorn.

It should cope with all that.

. As regards the hammers
mentioned I can see none of those in my shredder.

Oh gosh, what is going on ,,, ?

There is a disk which
has cutters on, on the reverse side is a cutter to deal with bigger
sticks.

Oh umm, I dunno what to say
a) have they changed the design ?
or
b) is there more than one Allen shredder
or c) were you not looking in the right place ( I think we can reject
that ! )

wrt (a) I said in my previous post in the original "Shredders" thread
that I could be many years out of date !
Anyhows :
my Allen has a 3 bladed cutter, like a rotary mower on its side but
with 3 instead if 2 blades mounted on the boss(protruding hub) at the
centre of the disk.
On the reverse of this disk it the chipper blade that is a bit like a
blade out of a woodworking plane.

BUT the disc also has a web, (cast in ?) of the same thickness
(approx, I think !) as the hub, which supports at the disk periphery
3 sets of 3 fingers/flails/hammers that do the shredding ( the cutter
blades just cut the stuff up into small bits that are then mashed up
and pulverised by the flails.

Hmmm, it is a bit difficult to describe in words ! The 3 mountings
each support 3 flails, and the axis of the pivot for each flail, one
in front of the other, is aligned with the axis of rotation of the
disk.

It is sort of like a disk with 3 bolts fixed to the edge, each bolt is
in line with the axis of the disk, each bolt carries 3 spaced out
flails, Thes flails are flung outwards and poke between the grating
that is the output grill.

So if you dont have them then it is just a glorified rotary mower,
and I am very puzzled ! :( (**)

Incidentally feeding sticks in is a bit of a problem, as they
are not drawn in but need feeding all the way,

with mine there is some drawing in of the stick, but depending upon
shape and nobbly bits I sometimes have to shove the last bit in by
hand, well NO! not by hand but with another stick as a 'dolly'.
it is as well to have such a sacrificial stick to hand, it can be kept
for reuse if you are carefull with its use, but better that than your
fingers !

which of course is not
possible, without finger risk.

perish the thought !

Finally there is a metal bar, about 4cm
wide, 25cm long with a hole at one end and chamfered at the other, what
is that for please?

I dont recognise that :( so either I have a brain failure or there is
summat different, back to (a) or (b) :-(

(**)
Does your machine look like this, which I linked in the original
thread :
http://www.mowdirect.co.uk/acatalog/...DERS_1100.html
(beware word wrap)

Allen shredder & similar users help
 

"WaltA" wrote in message
...
On Fri, 03 Aug 2007 18:23:33 +0100, Broadback wrote:
WaltA wrote:
Have you got it sorted ?

Having been away for a couple of days

Phew, that's a relief, I thought for a mo. you might have thrown it
off a high cliff in frustration !

I have not yet tried all the
recommendation's, for which I thank you. I am shredding cuttings from
holly, beech and mainly hawthorn.

It should cope with all that.

. As regards the hammers
mentioned I can see none of those in my shredder.

Oh gosh, what is going on ,,, ?

There is a disk which
has cutters on, on the reverse side is a cutter to deal with bigger
sticks.

Oh umm, I dunno what to say
a) have they changed the design ?
or
b) is there more than one Allen shredder
or c) were you not looking in the right place ( I think we can reject
that ! )

wrt (a) I said in my previous post in the original "Shredders" thread
that I could be many years out of date !
Anyhows :
my Allen has a 3 bladed cutter, like a rotary mower on its side but
with 3 instead if 2 blades mounted on the boss(protruding hub) at the
centre of the disk.
On the reverse of this disk it the chipper blade that is a bit like a
blade out of a woodworking plane.

BUT the disc also has a web, (cast in ?) of the same thickness
(approx, I think !) as the hub, which supports at the disk periphery
3 sets of 3 fingers/flails/hammers that do the shredding ( the cutter
blades just cut the stuff up into small bits that are then mashed up
and pulverised by the flails.

Hmmm, it is a bit difficult to describe in words ! The 3 mountings
each support 3 flails, and the axis of the pivot for each flail, one
in front of the other, is aligned with the axis of rotation of the
disk.

It is sort of like a disk with 3 bolts fixed to the edge, each bolt is
in line with the axis of the disk, each bolt carries 3 spaced out
flails, Thes flails are flung outwards and poke between the grating
that is the output grill.

So if you dont have them then it is just a glorified rotary mower,
and I am very puzzled ! :( (**)

Incidentally feeding sticks in is a bit of a problem, as they
are not drawn in but need feeding all the way,

with mine there is some drawing in of the stick, but depending upon
shape and nobbly bits I sometimes have to shove the last bit in by
hand, well NO! not by hand but with another stick as a 'dolly'.
it is as well to have such a sacrificial stick to hand, it can be kept
for reuse if you are carefull with its use, but better that than your
fingers !

which of course is not
possible, without finger risk.

perish the thought !

Finally there is a metal bar, about 4cm
wide, 25cm long with a hole at one end and chamfered at the other, what
is that for please?

I dont recognise that :( so either I have a brain failure or there is
summat different, back to (a) or (b) :-(

(**)
Does your machine look like this, which I linked in the original
thread :
http://www.mowdirect.co.uk/acatalog/...DERS_1100.html
(beware word wrap)

They do produce different models, leaf chipper/shredder and
chipper/shredder.
The former have serreted shredder blades, and the latter a blade and
hammers.

Have a look on the Mackissic website to see if they have parts diagrams to
help identify your machine.

Cheers
Anthony

Allen shredder & similar users help
 

On Sat, 4 Aug 2007 00:56:35 +0100, "Anthony" wrote:

Have a look on the Mackissic website to see if they have parts diagrams to
help identify your machine.

Thanks for the link

From the home page go to "consumer"
on the resulting "CONSUMER LINE-UP " page go to
"Leaf Shredder and Chipper"
click on LSC506IC

Externally mine is that shape but painted red, it has a 5hp B&S
engine, not 6.5 as shown.

Back up to "CONSUMER LINE-UP " page and then click on
"MIGHTY MAC PARTS BREAK DOWN "and download the pdf.

most parts look similar to my machine except for
9a "Shredder Plate Weldment", mine is quite different
and
11 "Shredder Rack Teeth" is absent in my machine.

Not shown in that pdf are 3 sets of 3 flails/hammers nor the 3 pivot
assemblies.

22 "Bar Screen" is similar to that on my machine and it is through the
three slots in that screen that the outer portions of each flail pass.

[In fact on the demo machine a bearing on the mainshaft developed some
'play' and the flails did no longer pass through the slots and the
whole enterpise came to a screeching halt ! ]

I presume that the 3 blades are now part of 9a on the side not shown ?
I presume that "weldment" means a welded/fabricated plate whereas,
from memory, mine is a "3D" casting,
I say 3D to imply considerable thickness in the axial direction with
all its webs and supports for the flail pivots.

So, to cut a long story short, it seems that they have changed the
design of the main functional item :(

Allen shredder & similar users help
 

I presume that the 3 blades are now part of 9a on the side not shown ?

Oh, sillyme ! When Broadback said
"There is a disk which has cutters on"
I imagined cutting blades like on mine, but now I see that
11"Shredder Rack Teeth"
I suppose those are the new cutters ?

Allen shredder & similar users help
 

WaltA wrote:
I presume that the 3 blades are now part of 9a on the side not shown ?

Oh, sillyme ! When Broadback said
"There is a disk which has cutters on"
I imagined cutting blades like on mine, but now I see that
11"Shredder Rack Teeth"
I suppose those are the new cutters ?


Many thanks everyone for your help, indeed Walt it is as you described,
very clear. I have just happily shred my hedge clippings in record time
with no jams. I "turned" the piles yesterday so that the moister on the
bottom dried off, also I kept and eye on the bag, when it stopped
jumping with excitement (about 1/2 full) I stopped and emptied it. Which
did the trick I do not know, will see how it deals with my fruit tree
prunings and leaves later in the year. I am disappointed with the branch
cutter, I would have expected it to pull them through once started. The
result is the last foot or so cannot be chopped.

Allen shredder & similar users help
 

On Sat, 04 Aug 2007 14:30:33 +0100, Broadback wrote:
WaltA wrote:
I presume that the 3 blades are now part of 9a on the side not shown ?

Oh, sillyme ! When Broadback said
"There is a disk which has cutters on"
I imagined cutting blades like on mine, but now I see that
11"Shredder Rack Teeth"
I suppose those are the new cutters ?


Many thanks everyone for your help, indeed Walt it is as you described,
very clear. I have just happily shred my hedge clippings in record time
with no jams. I "turned" the piles yesterday so that the moister on the
bottom dried off,

Hi Broadback
It's good to hear that you are getting better results with it,
tis a shame that it needs a two stage process tho, I like to get my
jobs done all in one go before lethargy, and a can of beer, has a
chance to set in :) :)

It is very disconcerting to recommend a product to someone and then to
find out that the manufacturer has messed about with the design in the
interim and b*tt***ed it up !

It would be interesting to know from the other recommenders which
variation they have.

And it is a salutory lesson for me to look after mine with tender
loving care cos I will not be able to replace it :-!(

I am disappointed with the branch
cutter, I would have expected it to pull them through once started. The
result is the last foot or so cannot be chopped.

Did you note my suggestion of keeping a spare bit of branch as a
sacrificial pokeing device to get that last foot or so pushed thro'

I wonder if they have changed the way the blade is mounted wrt its
chamfer ? (might be worth an experiment if it is reversible.
I cannot remember which way mine is mounted but it does have a bit of
pull through, although sometimes the last foot or so slows down and
rattles a bit, so I usually use a helper poker.

Allen shredder & similar users help
 

On Tue, 07 Aug 2007 23:30:09 GMT, WaltA wrote:

It is very disconcerting to recommend a product to someone and then to
find out that the manufacturer has messed about with the design in the
interim and b*tt***ed it up !

Agreed :-(

It would be interesting to know from the other recommenders which
variation they have.

From your description of your Allen shredder and suggestions, it would
seem that I have *exactly* the same model as you - I'd have said almost the
same as you about my machine.

Model LSC 505

and a couple of photos :-

www.troytheblacklab.co.uk/allen

Here's hoping that Broadback manages to find things a bit easier with more
practice (took me a little time).

Still love my Allen :-)
--
Regards,

Hugh Jampton

Allen shredder & similar users help
 

Hugh Jampton wrote:
On Tue, 07 Aug 2007 23:30:09 GMT, WaltA wrote:

It is very disconcerting to recommend a product to someone and then to
find out that the manufacturer has messed about with the design in the
interim and b*tt***ed it up !

Agreed :-(

It would be interesting to know from the other recommenders which
variation they have.

From your description of your Allen shredder and suggestions, it would
seem that I have *exactly* the same model as you - I'd have said almost the
same as you about my machine.

Model LSC 505

and a couple of photos :-

www.troytheblacklab.co.uk/allen

Here's hoping that Broadback manages to find things a bit easier with more
practice (took me a little time).

Still love my Allen :-)
I think the answer to the alteration of design will be cost cutting. :-(
another question please. Supplied with mine is a piece of metal, painted
black, about 220x25x3mm, at one end is a hole, both ends hace the ends
chamfered to form a three sided end. any ideas what it is for? I cannot
see it in the parts list.

Allen shredder & similar users help
 

On Thu, 09 Aug 2007 14:23:50 +0100, Broadback wrote:
(snips)
Hugh Jampton wrote:
On Tue, 07 Aug 2007 23:30:09 GMT, WaltA wrote:
and a couple of photos :-
www.troytheblacklab.co.uk/allen

Good pics, looks brand new ! ;)
mine is almost identical except it has more rivets holding the flexi
cover on the chipper chute.
Which is of little consequence except that it has made me think :

Over the years bits (tongues) have broken off that flexi and I got a
quote from my local garden machinery man - an extortionate sum was
mentioned ( he did warn me to hold on to my hat while he made his call
to his supplier ! )
I wonder if I was quoted for the whole flexi + steel chute ??
Cos with it riveted on like that it isnt exactly a routine
maintenance/service job I suppose

I never did replace it, not much comes back out but eye protection is
still a good idea.

I have made two mods to mine,
The hand-holds on the lip of the chute are a bit severe ( for my
delicate hands and I live on a hillside !)
so I have used some bits (2 short and 1 long) of garden hose, slit
lenghtwise and slotted over the steel, to round of and make more
comfortable those handholds.

and I have removed the steel + flexi baffle partway down the chute in
front of the throat,
On the grounds that it will not prevent anyone stupid enough to put
his arm all the way in anyway, and it caused a minor restriction when
dealing with a tangle of brambles !

I think the answer to the alteration of design will be cost cutting. :-(

I fear that you are right :(

another question please. Supplied with mine is a piece of metal, painted
black, about 220x25x3mm, at one end is a hole, both ends hace the ends
chamfered to form a three sided end. any ideas what it is for? I cannot
see it in the parts list.

I'm sorry I cant help, I dont recall anything like that with mine.

I suppose you could drive it into the ground like a tent peg and
tether the beast to it to stop it wandering off ?
I jest only partly ! - because there is no brake on the wheels and
because I live on a hill, there is a tendency for it to go walkabout
under its own vibrations ! :( Chocks are needed.

Allen shredder & similar users help
 

WaltA wrote:
On Thu, 09 Aug 2007 14:23:50 +0100, Broadback wrote:
(snips)
Hugh Jampton wrote:
On Tue, 07 Aug 2007 23:30:09 GMT, WaltA wrote:
and a couple of photos :-
www.troytheblacklab.co.uk/allen

Good pics, looks brand new ! ;)
mine is almost identical except it has more rivets holding the flexi
cover on the chipper chute.
Which is of little consequence except that it has made me think :

Over the years bits (tongues) have broken off that flexi and I got a
quote from my local garden machinery man - an extortionate sum was
mentioned ( he did warn me to hold on to my hat while he made his call
to his supplier ! )
I wonder if I was quoted for the whole flexi + steel chute ??
Cos with it riveted on like that it isnt exactly a routine
maintenance/service job I suppose

I never did replace it, not much comes back out but eye protection is
still a good idea.

I have made two mods to mine,
The hand-holds on the lip of the chute are a bit severe ( for my
delicate hands and I live on a hillside !)
so I have used some bits (2 short and 1 long) of garden hose, slit
lenghtwise and slotted over the steel, to round of and make more
comfortable those handholds.

and I have removed the steel + flexi baffle partway down the chute in
front of the throat,
On the grounds that it will not prevent anyone stupid enough to put
his arm all the way in anyway, and it caused a minor restriction when
dealing with a tangle of brambles !

I think the answer to the alteration of design will be cost cutting. :-(

I fear that you are right :(

another question please. Supplied with mine is a piece of metal, painted
black, about 220x25x3mm, at one end is a hole, both ends hace the ends
chamfered to form a three sided end. any ideas what it is for? I cannot
see it in the parts list.

I'm sorry I cant help, I dont recall anything like that with mine.

I suppose you could drive it into the ground like a tent peg and
tether the beast to it to stop it wandering off ?
I jest only partly ! - because there is no brake on the wheels and
because I live on a hill, there is a tendency for it to go walkabout
under its own vibrations ! :( Chocks are needed.


Your fault Walt, no grounds for compensation there, the instructions
insist that it must only be used on level ground. ;-)

Allen shredder & similar users help
 

I jest only partly ! - because there is no brake on the wheels and
because I live on a hill, there is a tendency for it to go walkabout
under its own vibrations ! :( Chocks are needed.

Your fault Walt, no grounds for compensation there, the instructions
insist that it must only be used on level ground. ;-)

Mea (partly) culpa !
I do have some level ground, terraced,, it eventually walks off that
as well ;) but it is easier to restrain than a goat

PS did I ever recommend a goat ?
(if I did, then beware ;) )
(ducks&runs )

Allen shredder & similar users help
 

On Thu, 09 Aug 2007 23:15:34 GMT, WaltA wrote:

and I have removed the steel + flexi baffle partway down the chute in
front of the throat,

My baffle broke away by itself. I've no intention of replacing it.

On the grounds that it will not prevent anyone stupid enough to put
his arm all the way in anyway, and it caused a minor restriction when
dealing with a tangle of brambles !

I'm the only one using my Allen - if anyone else used it I might just think
of replacing guards :-) SWMBO produces *lots* of stuff to be shredded but
she doesn't use the Allen - ever since she tried it for the first time
about 15 years ago - no way :-)

BTW My Allen is *very* noisy (5 HP B&S engine) - is yours ? I need ear
protection when I use it. I feel very guilty when I start it up and it
upsets the neighbours - we have lovely neighbours and I felt very bad
yeasterday starting up my Allen half way through their birthday party for
their beautiful 11 year old daughter - a 12 hour party with constant BOOM
BOOM music. I really do feel so guilty ;-)
--
Regards,

Hugh Jampton

Allen shredder & similar users help
 

On Sat, 11 Aug 2007 23:02:38 +0100, Hugh Jampton wrote:
On Thu, 09 Aug 2007 23:15:34 GMT, WaltA wrote:
and I have removed the steel + flexi baffle partway down the chute in
front of the throat,

My baffle broke away by itself.

Yer onner, g%ds truff

I've no intention of replacing it.

Quite right, elfinsfateegornmad, where are they when u need em in the
middle of a few acres of rampant undergrowth
Wimping on about ragwort I'll be bound !

ever since she tried it for the first time
about 15 years ago - no way :-)

Oh gorn,. do tell ;-)

BTW My Allen is *very* noisy (5 HP B&S engine) - is yours ?I need ear
protection when I use it.

No not at all, very comfortable without

I feel very guilty when I start it up and it
upsets the neighbours - we have lovely neighbours and I felt very bad
yeasterday starting up my Allen half way through their birthday party for
their beautiful 11 year old daughter - a 12 hour party with constant BOOM
BOOM music. I really do feel so guilty ;-)

Ah ha! Oh I see, you had me there !!, for a mo

Do you remeber in ,,, ohh tit mustav been in t' 60s, a craze for
woofers encased in concrete,
with a shelter over the top concrete is very outdoor friendly for
deliverin a goodly bit of Beethoven ;-)

Allen shredder & similar users help
 

--
Via: http://www.jumlers.com/uk.rec.gardening/
Take off the screen and throw it away. Problem solved!