GardenBanter.co.uk

GardenBanter.co.uk (https://www.gardenbanter.co.uk/)
-   United Kingdom (https://www.gardenbanter.co.uk/united-kingdom/)
-   -   SOT - splitting cypress rounds (https://www.gardenbanter.co.uk/united-kingdom/215710-sot-splitting-cypress-rounds.html)

Jeff Layman[_2_] 18-09-2018 06:53 PM

SOT - splitting cypress rounds
 
Many years ago we had an old cypress (probably C. lawsoniana) cut down.
The trunk was cut into rounds which were left to dry out for use in our
log-burning stove.

I've just got round to splitting the rounds and to say it has been
difficult is a bit of an understatement!. Basically, the wood was still
pretty tough (no splits on drying), but, even allowing for that, when
split through the pieces did not separate. On close examination, there
were what looked like several "internal branches" through the centre of
the wood, acting a bit like rebars in concrete. In the end I used a
chisel to cut through them. See photos he

https://imgur.com/a/FTRBaXc

The first shows the "rebars" cut through each side of the split. The
second shows the varying angles they take (see top right one in
particular). The third shows each side of a split log showing the path
of the "rebar".

Anyone seen anything like this before? What are they?

--

Jeff

Andy Burns[_7_] 18-09-2018 07:26 PM

SOT - splitting cypress rounds
 
Chris Hogg wrote:

Jeff Layman wrote:

https://imgur.com/a/FTRBaXc
The first shows the "rebars"
Anyone seen anything like this before? What are they?


Surely they are the remains of side branches


That normally end-up as knots in sawn timber

Jeff Layman[_2_] 18-09-2018 07:43 PM

SOT - splitting cypress rounds
 
On 18/09/18 19:08, Chris Hogg wrote:
On Tue, 18 Sep 2018 18:53:16 +0100, Jeff Layman
wrote:

Many years ago we had an old cypress (probably C. lawsoniana) cut down.
The trunk was cut into rounds which were left to dry out for use in our
log-burning stove.

I've just got round to splitting the rounds and to say it has been
difficult is a bit of an understatement!. Basically, the wood was still
pretty tough (no splits on drying), but, even allowing for that, when
split through the pieces did not separate. On close examination, there
were what looked like several "internal branches" through the centre of
the wood, acting a bit like rebars in concrete. In the end I used a
chisel to cut through them. See photos he

https://imgur.com/a/FTRBaXc

The first shows the "rebars" cut through each side of the split. The
second shows the varying angles they take (see top right one in
particular). The third shows each side of a split log showing the path
of the "rebar".

Anyone seen anything like this before? What are they?


Surely they are the remains of side branches that, if not apparent on
the surface, have snapped off at an earlier stage of the tree's
growth, and the stumps have been overgrown by the expanding trunk so
that they are no longer visible on the outside, in much the same way
as a trunk will 'swallow' fence wire or nails etc or even bicycles!
https://tinyurl.com/y9fbupgy


I didn't think of that! They do look like branches, but why have I never
noticed them before when splitting other cypress, birch, cherry, sorbus,
etc? I can understand metal from bicycles and other objects remaining in
trees, but I would have thought a tree would have been able to recycle
its own lignin into something usable. Or, if not, form a callous at the
growth point and allow the rest to drop off.

Or am I missing the plot completely and these, in sawn wood, form the knots?

--

Jeff

David Hill 21-09-2018 01:18 AM

SOT - splitting cypress rounds
 
On 18/09/2018 19:43, Jeff Layman wrote:
On 18/09/18 19:08, Chris Hogg wrote:
On Tue, 18 Sep 2018 18:53:16 +0100, Jeff Layman
wrote:

Many years ago we had an old cypress (probably C. lawsoniana) cut down.
The trunk was cut into rounds which were left to dry out for use in our
log-burning stove.

I've just got round to splitting the rounds and to say it has been
difficult is a bit of an understatement!. Basically, the wood was still
pretty tough (no splits on drying), but, even allowing for that, when
split through the pieces did not separate. On close examination, there
were what looked like several "internal branches" through the centre of
the wood, acting a bit like rebars in concrete. In the end I used a
chisel to cut through them. See photos he

https://imgur.com/a/FTRBaXc

The first shows the "rebars" cut through each side of the split. The
second shows the varying angles they take (see top right one in
particular). The third shows each side of a split log showing the path
of the "rebar".

Anyone seen anything like this before? What are they?


Surely they are the remains of side branches that, if not apparent on
the surface, have snapped off at an earlier stage of the tree's
growth, and the stumps have been overgrown by the expanding trunk so
that they are no longer visible on the outside, in much the same way
as a trunk will 'swallow' fence wire or nails etc or even bicycles!
https://tinyurl.com/y9fbupgy


I didn't think of that! They do look like branches, but why have I never
noticed them before when splitting other cypress, birch, cherry, sorbus,
etc? I can understand metal from bicycles and other objects remaining in
trees, but I would have thought a tree would have been able to recycle
its own lignin into something usable. Or, if not, form a callous at the
growth point and allow the rest to drop off.

Or am I missing the plot completely and these, in sawn wood, form the
knots?

They are absorbed into the trunk making it much stronger. The wood is
harder the longer left.
The easier wat to split is from the bottom of the log, still not easy

Jeff Layman[_2_] 21-09-2018 08:07 AM

SOT - splitting cypress rounds
 
On 21/09/18 01:18, David Hill wrote:
On 18/09/2018 19:43, Jeff Layman wrote:
On 18/09/18 19:08, Chris Hogg wrote:
On Tue, 18 Sep 2018 18:53:16 +0100, Jeff Layman
wrote:

Many years ago we had an old cypress (probably C. lawsoniana) cut down.
The trunk was cut into rounds which were left to dry out for use in our
log-burning stove.

I've just got round to splitting the rounds and to say it has been
difficult is a bit of an understatement!. Basically, the wood was still
pretty tough (no splits on drying), but, even allowing for that, when
split through the pieces did not separate. On close examination, there
were what looked like several "internal branches" through the centre of
the wood, acting a bit like rebars in concrete. In the end I used a
chisel to cut through them. See photos he

https://imgur.com/a/FTRBaXc

The first shows the "rebars" cut through each side of the split. The
second shows the varying angles they take (see top right one in
particular). The third shows each side of a split log showing the path
of the "rebar".

Anyone seen anything like this before? What are they?

Surely they are the remains of side branches that, if not apparent on
the surface, have snapped off at an earlier stage of the tree's
growth, and the stumps have been overgrown by the expanding trunk so
that they are no longer visible on the outside, in much the same way
as a trunk will 'swallow' fence wire or nails etc or even bicycles!
https://tinyurl.com/y9fbupgy


I didn't think of that! They do look like branches, but why have I never
noticed them before when splitting other cypress, birch, cherry, sorbus,
etc? I can understand metal from bicycles and other objects remaining in
trees, but I would have thought a tree would have been able to recycle
its own lignin into something usable. Or, if not, form a callous at the
growth point and allow the rest to drop off.

Or am I missing the plot completely and these, in sawn wood, form the
knots?

They are absorbed into the trunk making it much stronger. The wood is
harder the longer left.


Anyone got any links on the internet which actually states this? I am
not doubting the statement at all - I agree with it. But why have I
seen it now only in these cypress logs, and not other types of wood?

The easier wat to split is from the bottom of the log, still not easy


Is there an easy way to tell top from bottom of an otherwise uniform
appearance log? But you are right - I gave up trying to split some logs
which had branched, even though the rounds were only 10 cm thick. I'll
have to saw through them.

--

Jeff

Janet 21-09-2018 12:36 PM

SOT - splitting cypress rounds
 
In article , lid
says...
Subject: SOT - splitting cypress rounds
From: Jeff Layman
Newsgroups: uk.rec.gardening

On 21/09/18 01:18, David Hill wrote:
[quoted text muted]
Or am I missing the plot completely and these, in sawn wood, form the
knots?

They are absorbed into the trunk making it much stronger. The wood is
harder the longer left.


Anyone got any links on the internet which actually states this? I am
not doubting the statement at all - I agree with it. But why have I
seen it now only in these cypress logs, and not other types of wood?

The easier wat to split is from the bottom of the log, still not easy


Is there an easy way to tell top from bottom of an otherwise uniform
appearance log? But you are right - I gave up trying to split some logs
which had branched, even though the rounds were only 10 cm thick. I'll
have to saw through them.


Let the logs dry under cover until some small gap/split shows where
you can drive in a log bomb. Much more effective than an axe.

https://www.amazon.co.uk/Splitter-17...itting-Easily-
Grenade/dp/B0091SW1NQ

Janet.


Jeff Layman[_2_] 21-09-2018 01:22 PM

SOT - splitting cypress rounds
 
On 21/09/18 12:36, Janet wrote:
In article , lid
says...
Subject: SOT - splitting cypress rounds
From: Jeff Layman
Newsgroups: uk.rec.gardening

On 21/09/18 01:18, David Hill wrote:
[quoted text muted]
Or am I missing the plot completely and these, in sawn wood, form the
knots?

They are absorbed into the trunk making it much stronger. The wood is
harder the longer left.


Anyone got any links on the internet which actually states this? I am
not doubting the statement at all - I agree with it. But why have I
seen it now only in these cypress logs, and not other types of wood?

The easier wat to split is from the bottom of the log, still not easy


Is there an easy way to tell top from bottom of an otherwise uniform
appearance log? But you are right - I gave up trying to split some logs
which had branched, even though the rounds were only 10 cm thick. I'll
have to saw through them.


Let the logs dry under cover until some small gap/split shows where
you can drive in a log bomb. Much more effective than an axe.

https://www.amazon.co.uk/Splitter-17...itting-Easily-
Grenade/dp/B0091SW1NQ


These logs are at least 6 years old and have always been under cover.
Very few show splits, and in those that do the splits are barely a mm
across and 3 or 4 cm long. I am using a small splitting axe (4 cm wide
head with 35 cm handle) - not chopping axe - and once jammed in use a
club hammer to drive it in further. Because of the internal "reinforcing
branches" it makes no difference even when the axe head is level with
the edge of the log - the two pieces do not separate until the branch is
cut with a chisel.

Logs of other wood stored for similar lengths of time show wide cracks
- up to 4 or 5mm and 7 or 8 cm long. If I hit these accurately with the
axe, I can split the log with one hit. If I drive the axe in with the
hammer, it takes only two or three blows to split the log completely apart.

--

Jeff

Andy Burns[_7_] 21-09-2018 08:30 PM

SOT - splitting cypress rounds
 
Jeff Layman wrote:

The second one is fascinating.


I came across this more gruesome example while searching for the images
that I knew I'd seen before ...

https://allthatsinteresting.com/stuckie-mummy-dog


All times are GMT +1. The time now is 01:51 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
GardenBanter