GardenBanter.co.uk

GardenBanter.co.uk (https://www.gardenbanter.co.uk/)
-   Lawns (https://www.gardenbanter.co.uk/lawns/)
-   -   Mower Engine Problem(s) (https://www.gardenbanter.co.uk/lawns/61604-mower-engine-problem-s.html)

Greg 18-05-2004 05:11 AM

Mower Engine Problem(s)
 
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.

Steveo 18-05-2004 05:11 AM

Mower Engine Problem(s)
 
(Greg) wrote:
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.

Does the oil smell like gas?

--
http://www.allpar.com/mopar.html

Greg 18-05-2004 03:17 PM

Mower Engine Problem(s)
 
Steveo wrote in message ...
(Greg) wrote:
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.

Does the oil smell like gas?



Yes, a little, but doesn't most used oil have a gas smell? What's you
analysis if it does have a gas smell?

mudpiemaker42 18-05-2004 08:17 PM

Mower Engine Problem(s)
 
on the old briggs motors the hose that went to the carb. was a crankcase
breather [a valve that let vapor or pressure out of the crankcase] it could
go bad and let oil blow into the carb. this may be the same thing on the
newer motors
"Steveo" wrote in message
...
(Greg) wrote:
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.

Does the oil smell like gas?

--
http://www.allpar.com/mopar.html




Steveo 19-05-2004 02:07 AM

Mower Engine Problem(s)
 
(Greg) wrote:
Steveo wrote in message
...
(Greg) wrote:
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades,
then it would resume normal rev speed. I checked a few things, and
noticed a rubber hose that attached to the carb from the engine had
came lose from the carb. I placed it back on, added oil (as I always
do when it's needed), and mowed the grass. When I finished, I turned
the mower off and restarted to see if the high revs woul dhappen
again. When I did, a large amount of oil blew out the rubber hose I
had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.

Does the oil smell like gas?


Yes, a little, but doesn't most used oil have a gas smell? What's you
analysis if it does have a gas smell?

It might be the carb.

http://www.small-engines.com/gasleak.html

--
And it's twice as hard on my stride
When I take a day and let it ride. - Paul Cotton.

gerald whitaker 24-05-2004 12:08 AM

Mower Engine Problem(s)
 
It sounds like there is too much oil in it. Check it or drain the sump and
refill with the proper amount.
"Greg" wrote in message
om...
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.




Greg 27-05-2004 09:22 PM

Mower Engine Problem(s)
 
(Greg) wrote in message . com...
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.



Well, the service guy looked at this engine. The cause of failure was
due to a ventilation hose detaching and sucking dirt/dust into the
engine. The hose, apparently, connects to the engine from the carb.
Briggs agreed to replace the full engine, even though it is 2 months
out of warranty. Thank you B&S.

The service guy wants $360 to do the work, plus filters, plug, and
oil. Does that seem like a reasonable rate? He says he is going by the
B&S labor rate guide.

Chip Stein 29-05-2004 03:17 AM

Mower Engine Problem(s)
 
Well, the service guy looked at this engine. The cause of failure was
due to a ventilation hose detaching and sucking dirt/dust into the
engine. The hose, apparently, connects to the engine from the carb.
Briggs agreed to replace the full engine, even though it is 2 months
out of warranty. Thank you B&S.

The service guy wants $360 to do the work, plus filters, plug, and
oil. Does that seem like a reasonable rate? He says he is going by the
B&S labor rate guide.


that's a shortblock not a complete engine. and if it's sucked up
enough dirt the throttle shaft will be worn in the carb. tell them
you want briggs to cover a new carb also. it will be trouble down the
road if they don't.
i managed a small engine shop for several years and have seen it
before.
Chip

Greg 29-05-2004 06:04 PM

Mower Engine Problem(s)
 
(Greg) wrote in message . com...
(Greg) wrote in message . com...
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.


Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.



Well, the service guy looked at this engine. The cause of failure was
due to a ventilation hose detaching and sucking dirt/dust into the
engine. The hose, apparently, connects to the engine from the carb.
Briggs agreed to replace the full engine, even though it is 2 months
out of warranty. Thank you B&S.

The service guy wants $360 to do the work, plus filters, plug, and
oil. Does that seem like a reasonable rate? He says he is going by the
B&S labor rate guide.


that's a shortblock not a complete engine. and if it's sucked up
enough dirt the throttle shaft will be worn in the carb. tell them
you want briggs to cover a new carb also. it will be trouble down the
road if they don't.
i managed a small engine shop for several years and have seen it
before.


He told me that it was a long block (complete engine) less the fly wheel.

caj 17-06-2004 10:56 AM

Mower Engine Problem(s)
 
Quote:

Originally posted by Greg
(Greg) wrote in message . com...
(Greg) wrote in message . com...
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago. When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades, then
it would resume normal rev speed. I checked a few things, and noticed
a rubber hose that attached to the carb from the engine had came lose
from the carb. I placed it back on, added oil (as I always do when
it's needed), and mowed the grass. When I finished, I turned the mower
off and restarted to see if the high revs woul dhappen again. When I
did, a large amount of oil blew out the rubber hose I had reconnected.

I'm afraid this may not be good news. This engine has been well cared
for - regular oil and filter changes, etc. I had a similar problem
with another B&G engine a few years ago. I will not be buying another
mower with a Briggs engine mounted in it.


Anyhow, obviously, I need to fix this 2 year old mower. Before I tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.



Well, the service guy looked at this engine. The cause of failure was
due to a ventilation hose detaching and sucking dirt/dust into the
engine. The hose, apparently, connects to the engine from the carb.
Briggs agreed to replace the full engine, even though it is 2 months
out of warranty. Thank you B&S.

The service guy wants $360 to do the work, plus filters, plug, and
oil. Does that seem like a reasonable rate? He says he is going by the
B&S labor rate guide.


that's a shortblock not a complete engine. and if it's sucked up
enough dirt the throttle shaft will be worn in the carb. tell them
you want briggs to cover a new carb also. it will be trouble down the
road if they don't.
i managed a small engine shop for several years and have seen it
before.


He told me that it was a long block (complete engine) less the fly wheel.

Sorry to butt in, but I have just received a used B&S mower with a backfire on shutoff. Were you able to get an answer to the problem of the backfire, or is this standard?

The engine runs fine, but everytime I shut it off, there is a good 1 backfire. Any help you can offer is appreciated.

mudpiemaker42 17-06-2004 06:08 PM

Mower Engine Problem(s)
 
the back fire is caused by detonation that's when you turn off the engine it
will turn over several more times sucking gas into the combustion chamber.
the engine is so hot that the gas ignites from the heat. the back fire you
hear is the explosion from the gas igniting. try letting your mower run at
idle for at least one minute before you turn it off also check idle speed
adj. it could be to running to fast at idle also check high speed fuel adj.
it could be running to lean making engine over heat
"caj" wrote in message
...

Greg wrote:
(Greg) wrote in message
. com...
(Greg) wrote in message

. com...
I have a 2 years, 2 months old Briggs and Stratton 14hp engine on

a
Troy-Bilt 42" chassis. It just ran out of warranty 2 months ago.

When
I first got the mower it would backfire every now and then. Last
summer it would blow a puff of smoke when I started the engine.

Today, the engine would rev very high until I engaged the blades,

then
it would resume normal rev speed. I checked a few things, and

noticed
a rubber hose that attached to the carb from the engine had came

lose
from the carb. I placed it back on, added oil (as I always do

when
it's needed), and mowed the grass. When I finished, I turned the

mower
off and restarted to see if the high revs woul dhappen again.

When I
did, a large amount of oil blew out the rubber hose I had

reconnected.

I'm afraid this may not be good news. This engine has been well

cared
for - regular oil and filter changes, etc. I had a similar

problem
with another B&G engine a few years ago. I will not be buying

another
mower with a Briggs engine mounted in it.

Anyhow, obviously, I need to fix this 2 year old mower. Before I

tear
down the engine, anyone want to suggest the problem based on the
symptoms? Thanks.


Well, the service guy looked at this engine. The cause of failure

was
due to a ventilation hose detaching and sucking dirt/dust into the
engine. The hose, apparently, connects to the engine from the

carb.
Briggs agreed to replace the full engine, even though it is 2

months
out of warranty. Thank you B&S.

The service guy wants $360 to do the work, plus filters, plug, and
oil. Does that seem like a reasonable rate? He says he is going by

the
B&S labor rate guide.


that's a shortblock not a complete engine. and if it's sucked up
enough dirt the throttle shaft will be worn in the carb. tell

them
you want briggs to cover a new carb also. it will be trouble down

the
road if they don't.
i managed a small engine shop for several years and have seen

it
before.


He told me that it was a long block (complete engine) less the fly
wheel. *


Sorry to butt in, but I have just received a used B&S mower with a

backfire on shutoff. Were you able to get an answer to the problem of
the backfire, or is this standard?

The engine runs fine, but everytime I shut it off, there is a good 1
backfire. Any help you can offer is appreciated.


--
caj
------------------------------------------------------------------------
posted via
www.GardenBanter.co.uk



----== Posted via Newsfeed.Com - Unlimited-Uncensored-Secure Usenet

News==----
http://www.newsfeed.com The #1 Newsgroup Service in the World! 100,000

Newsgroups
---= 19 East/West-Coast Specialized Servers - Total Privacy via Encryption

=---



caj 19-06-2004 08:57 AM

Mower Engine Problem(s)
 
[quote]Originally posted by mudpiemaker42
[b]the back fire is caused by detonation that's when you turn off the engine it
will turn over several more times sucking gas into the combustion chamber.
the engine is so hot that the gas ignites from the heat. the back fire you
hear is the explosion from the gas igniting. try letting your mower run at
idle for at least one minute before you turn it off also check idle speed
adj. it could be to running to fast at idle also check high speed fuel adj.
it could be running to lean making engine over heat
"caj" wrote in message
...[color=blue]

Thank you very much! I will do everything you have said.


All times are GMT +1. The time now is 07:19 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
GardenBanter