BulkHead Fittings
 

Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.

BulkHead Fittings
 

Kodiak wrote:

Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.


go to a lg. plumbing supply store or
a boat/marine dealer for those sizes


--
http://www.kencofish.com Ken Arnold,
401-781-9642 cell 401-225-0556
Importer/Exporter of Goldfish,Koi,rare Predators
Shipping to legal states/countries only!
Permalon liners, Oase & Supreme Pondmaster pumps


Please Note: No trees or animals were harmed in the
sending of this contaminant free message We do concede
that a signicant number of electrons may have been
inconvenienced ;)

BulkHead Fittings
 

Kodiak wrote:

Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.


go to a lg. plumbing supply store or
a boat/marine dealer for those sizes


--
http://www.kencofish.com Ken Arnold,
401-781-9642 cell 401-225-0556
Importer/Exporter of Goldfish,Koi,rare Predators
Shipping to legal states/countries only!
Permalon liners, Oase & Supreme Pondmaster pumps


Please Note: No trees or animals were harmed in the
sending of this contaminant free message We do concede
that a signicant number of electrons may have been
inconvenienced ;)

BulkHead Fittings
 

Try checking this site. It shows how to make them from other pvc parts.
really easy and really cheap to make.

-m


"Kodiak" wrote in message
...
Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.

BulkHead Fittings
 

what site?

"Megan" wrote in message
...
Try checking this site. It shows how to make them from other pvc parts.
really easy and really cheap to make.

-m


"Kodiak" wrote in message
...
Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.

BulkHead Fittings
 

Aquatic Ecosystems at http://www.aquaticeco.com has them, from "economy" to
"expensive". They also have something called Uniseals that are ideal for
installation in tanks, drums, etc. They're much cheaper, but they won't work
on items that have thickness, like going through a plywood tank. A 3/4"
Uniseal is only $2 A "brownie point" for the Uniseal is that you slide
your pvc through it, and it isn't glued. Therefore, you can push several
extra inches through it and adjust afterwards, just in case you find out
that you really needed a distance of 7" instead of the 6.25" you cut and
glued . . .

Lee

"Kodiak" wrote in message
...
Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.

BulkHead Fittings
 

I suggest using PVC to MPT and PVC to FPT (male and female pipe
thread) adapters. This works quite well with the 1 1/2" and 2" sizes
necessary for my barrel filter; smaller sizes should be even easier.

Make the hole just large enough to accomodate the male threads.
Ideally, you will be able to screw the male adapter easily into the
hole, but it will be snug enough you can't pull it out. Obviously,
the female adapter is screwed onto the male adapter and tightened down
to make a tight seal with the drum wall.

Some people suggest cutting a gasket from a scrap of pond liner
material. I simply coated the threads and mating surfaces liberally
with clear RTV before screwing the parts together. As a bonus, it
makes an excellent thread lubricant, making it easy to tighten the
parts together.

PlainBill

On Fri, 12 Sep 2003 01:41:42 -0400, "Kodiak"
wrote:

Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.

BulkHead Fittings
 

Oh wow, sorry about that. I blame it on being sometime way too late last
night when i posted. here it is. http://www.perigee.net/~jrjohns/web19.html

-m
"D Kat" wrote in message
...
what site?

"Megan" wrote in message
...
Try checking this site. It shows how to make them from other pvc parts.
really easy and really cheap to make.

-m


"Kodiak" wrote in message
...
Where can I get bulkhead fittings 1", 3/4", 1/2" without having to pay
a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to
the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you
can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.

BulkHead Fittings
 

Wow, thanks for all the info folks....
....Kodiak

"Megan" wrote in message
...
Oh wow, sorry about that. I blame it on being sometime way too late last
night when i posted. here it is.
http://www.perigee.net/~jrjohns/web19.html

-m
"D Kat" wrote in message
...
what site?

"Megan" wrote in message
...
Try checking this site. It shows how to make them from other pvc
parts.
really easy and really cheap to make.

-m


"Kodiak" wrote in message
...
Where can I get bulkhead fittings 1", 3/4", 1/2" without having to
pay
a
fortune. (mail order)
These are fittings with a nut on both sides so you can attach it to
the
bottom of a vessel or container,
eg: used to make a biological filter out of a plastic barrel, so you
can
attach a hose to a vessel etc...
My local hardware wants 28$ for a 3/4" fitting.