My pump now sits in a large plastic flower pot.
I've done that one too... and for the same reasons [poor little fish!!!].
It's effective, but the plant baskets are definitely an esthetic
improvement.
Mila
"Heather" wrote in message
. ..
I found out the hard way if you don't isolate the pump inside something
like
Rich and Mila are referring to, that you will loose small fish. My first
batch of feeder fish ended up getting chopped when they were sucked
through
the pump.
My pump now sits in a large plastic flower pot. Stretched over the top is
a
piece of plastic mesh (actually it is a cut up piece of mesh sleeve that
normally goes over a scuba tank). This is flexible so can be bent over
the
edges. Not pretty but it works. I like the mesh basket idea better.
Will
try that in the spring.
Heather
"BTC/TAK on ACK" wrote in message
...
... mesh type plant baskets, put the pump inside... tie the top basket
to
the bottom
basket... baskets have a larger surface to
clog, versus the foam filter, so it takes longer.
I've tried this, by the way, and it works quite well.
I have stretched a cut-off section from an old pair of [large... which
happen to be too easy to find in my house... work best] panty-hose leg
[twist-tied at the ends] around the connected baskets, when I've wanted
finer pre-pump straining.
Mila
"RichToyBox" wrote in message
news:G4HNb.77849$na.43117@attbi_s04...
My first ponds were preformed and my pumps were attached to the piping
with
a pipe union. The pipe union allows you to disconnect the pump from
the
piping without disturbing the piping that is buried under ground,
mulch
or
rock. I also put my pump cords, 10 - 20 feet depending on pump,
through
a
length of pvc pipe, which I buried so that no one would trip on the
loose
cords and they would not be a distraction. Today they run on top of
the
ground to the smaller pond.
As for prefilters, most of them are way undersized, made of foam, and
clog
quickly. Get some of the mesh type plant baskets, put the pump
inside,
run
the pipe through the top basket, and tie the top basket to the bottom
basket. The baskets are not as fine as the foam, but they are fine
enough
to prevent the pump from clogging. The baskets have a larger surface
to
clog, versus the foam filter, so it takes longer.
--
RichToyBox
http://www.geocities.com/richtoybox/pondintro.html
"rasta" wrote in message
...
hey all,
been reading through this group off and on since i started thinkin'
about ponding in '96. great group and with the old dejanews and now
google a fine source of info.
i will finally start digging the hole for my small goldfish/water
garden tomorrow. here's the plan and i have a few immediate
questions
on the finer things of the install:
i live in zone 9 of the good ole us of a. the pond will be formal in
nature 8x4x2 deep with two shelves facing away from the viewing area
(approx. 450 gals.) and will be situated under a patio cover
recieving
3 hrs. of direct sun and 6 hrs. of indiect. will be using 45 mil.
liner, a supreme 700 mag drive pump, and a bio force 1000 filter.
pump
will flow about 90% to the filter and discharge through a decorative
urn laid on its side side into the pond. i'll split 10% to a
spitting
statue. oh, and all elec. will be plugged into a gfi.
first round of ?s:
1 what type (if any) of prefilter do these pumps have. if the pump
needs to be lifted for cleaning, how do you guys cope with the extra
wiring/tubing left in the pond in order to raise the pump?
2 how to run the tubing/ wiring for pump out of pond? electrical
should probably have to be put in conduit to gfi. can i put the
tubing
and elec. through a piece if, say 2" pvc on the edge of the liner
and
put my coping stones between this pvc?
this'll get me going. there will be lots of other ?s to follow.
glad to be in on these discussions and hope to pass on some
knowledge
in the future.