Home |
Search |
Today's Posts |
#10
|
|||
|
|||
Stalling snowblower
Depends on the circumstances really. It doesn't take a small engine 20-30
minutes to get up to operating temperature. A fuel flow problem is definitely a possibility. As Srgnt points out, you can check the spark plug. If there's a reddish/glazed appearance to the plug, the engine could be running hot. Speaking of the spark plug, was it ever changed? Here's some examples of spark plug conditions: http://www.classictruckshop.com/club...k/wrong_ht.jpg If the choke isn't closing, the engine would be running too rich. Carb operating principles do not change with temperature. Mike "Srgnt Billko" wrote in message ... "Mike" wrote in message . .. I'm surprised to hear this is happening on a machine that is two years old. Did the machine ever sit for a long period of time with old gas? Snow blower engines don't usually have air cleaners on them (mine doesn't; I've worked on many that didn't). The whole reasoning with that is the season they're used for is not dusty. Winter air is somewhat clean. If the gumout doesn't help in a tankful, then there's a good chance it will require some manual cleaning. Do you know the model and make of your blower? I can try to find out what engine it is. Geez Mike - 2 years old ? Doesn't seem like it would have had a chance to get "dirty" or gummed up - and if it some times runs for 20 or 30 minutes I'd be looking for something else. It's easy (and cheap) to replace the spark plug. I've had mice nests under the shroud that cause motors to overheat. Is the choke opening up all the way ? If not, it would be starving for gas after heating up. "Frank Rosenbaum" wrote in message ... Thanks for the advice. This is its second winter. It was new last year. I forgot to add that I put some gumout in the fuel. How long does it take to 'work'? (Should I just try to let it run out of this tank of gas and refill it again?) {Even at $2.25 a gal. Gas is still cheaper than a trip to the repair shop.} There is no easily removable air cleaner. There is a shield next to the exhaust that covers the throttle, choke and 'key'. But the choke knob does not seem come off easily, if at all, and I am hesitant to force it. I could not find a model number for the engine. It is a 4 stroke I think it is a 5 horsepower two stage blower. I did not see any filters in the gas line between the tank and where it disappears into the engine body. The tube seems to be creased where it bends from the tank to the body, but since it is a soft tube, I don't think that is the problem. What else can I add? Thanks again Frank Still in snowy Michigan with about 4 more inches predicted by tomorrow "Mike" wrote in message . .. Depending on the age of your blower, it sounds like your carb might be dirty. Especially when you say it starts fine with the primer. You already ruled out the possibility of it being a "gravity" feed problem by loosening the cap, so that shouldn't be the issue. Do you have an inline filter going to the carb? I'd check that to make sure it's not clogged. If you want to attempt repair by yourself, it shouldn't be too much of a challenge. I would pick up a repair manual for your model Tecumseh so you can get an idea of the work involved before you start. As long as you have a socket/wrench set, screwdrivers, and regular and needle nose pliers. If there are jets in the carb that can be taken out with a screw driver, make sure your screwdriver is the right size, otherwise you may end up stripping it (I've done this many of times). Just make sure the screw driver is snug with the jet. I think the Tecumseh engines have a fixed jet in the bowl (again, depending on age). You may get lucky just by blowing the jets with compressed air (I assume you have an air compressor). Have you tried running a bottle of Gumout carb cleaner through the tank? Pick up some of that and mix it in proportion (one bottle treats a tank full in a car!). This shouldn't be too critical since it's combustible and is somewhat like a fuel. The theory of carburetors isn't difficult, so learning a little about them definitely may pay off for you in the future and save you lots of money. Knowledge learned now can be applied to your other pieces of equipment (weed wacker, chain saw, etc.). I've been in the small engine repair business for years, so feel free to ask any questions. Mike "Frank Rosenbaum" wrote in message ... Hi, all. I have a problem with my Yardman/Tecumseh snowblower stalling. It was run out of gas in the spring and worked ok for the first two times this year. Now, sometimes it will run for 20 or 30 minutes and then stall other times it won't even run long enough for me to get back to the handlebars. It always restarts if I push the primer button, but doesn't always stay running. The gas cap was dropped and the rubber part and the foam part came out. (Am I missing any pieces?) I think I put it back together the right way. (Foam on the post then covered by the rubber funnel with the wide part inside the cap and the narrow part facing into the gas tank). I have also run the blower with the cap loose. There is fresh gas in the tank. When the blower stalls, it almost sounds as if it isn't getting enough gas. I am not at all familiar with engines so I don't know where to start. I don't want to take it apart myself, but I will if it can be fixed by a DIY. Can anyone help?? Thanks Frank in Snowy Michigan |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
99 JGC Laredo 4.0L I6 stalling- Spam warning! | Ponds | |||
Stalling Snowblower - Update | Lawns | |||
Cub Cadet ... Stalling Problem | Gardening | |||
Mower stalling - help! | United Kingdom |