No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

"Mark Mendell" wrote in message
news:YX65c.14384$wg.2789@okepread01...
Priss,

What would I do differently?

As far as the bottom drain goes, not much. How big is your pond? I did a
pretty good job of getting mine in the lowest point, so it does a great
job.
The only mistake I made was when I was installing the liner, after I had
connected the bottom drain, I put a plastic cup into the bottom drain hole
to keep debris out, and told myself "Mark, if you don't remember to take
that cup out of the drain, you're going to be very VERY unhappy." Well,
guess what? Some creative snorkeling was in order.

To drain the pond, I then built a U-shaped bypass line that I install in
my
skimmer (directly connects the bottom drain to the pump). I can drain a
4500 pond in an hour, if I need to.

What else would I have done differently?

I was under the impression that when I filled it with water (estimated
4500
gallons), the liner would conform to the hole. Unfortunately, I ended up
with some folds that were unsightly. So, take care before you fill it!

I got a great deal on limestone, so that's what I used. I spent a very
hot
week in July 2 summers ago moving 20 ton of limestone from my driveway to
my
pond (rented a bobcat), and have spent my time ever since moving it back
out. I'm still trying to get rid of the "ring of rock" look.

In order to cover the unsightly creases and liner, I paniced and began
lining the pond with rock. If I were to do it again, I would take great
care with how my liner was laying before adding water, then add maybe a
few
large rocks. The liner will disappear eventually. The one up side is
that
with all of that limestone in my pond, my ph is very stable!

You're water is going to turn very green. Just be patient, plant lots of
plants, and it will clear. Don't waste your time with chemicals or UV
filters.

What would I NOT do differently?

Many folks on this site use veggie filters exclusively, and that sounds
like
a great way to go (not to mention much more inexpensive that my set-up).
On
the other hand, I can clean my bead filter whenever necessary in 10
minutes
from my basement. It's pretty slick. Depending on the season, I have to
do
it once per week to once every 2 weeks. Flushing it that often, I've seen
no ill effects on the fish.

My pond is outside my back door. I can hear it from my house, and see if
from my kitchen. I see lots of ponders around my area that put their
ponds
in the back of their yards. I love having to walk by and peer into mine
every time I leave the house.

I got the bug from my parents, who have a small pond in Kansas (perhaps 5'
by 10') By the second season, they were wishing it were MUCH bigger. I
decided to build as large a pond as I could manage (to my wife's original
dismay). It's 15' x 30' x 4' deep, with 2 water falls and a smaller
"feeder" pond above. I've yet to wish for more pond, and my family loves
it.

I'll bet that response was more than you bargained for, huh!

Mark


"pmwebdesigns" wrote in message
...
Mark, what would you do different if you had to.
I want two bottom drains on my new pond ( digging next month) and don't
have
a clue what to do.
I went to 3 book stores over the weekend in search of a good pond book.
There were plenty to be found but none had anything on bottom drains!!!!
I was hoping to find something on drains to show me how to set it up and
so
fourth.
Priss


"Mark Mendell" wrote in message
news:t5Z4c.8358$wg.5252@okepread01...
Nedra,

It's a Tetra 3 inch, plumbed through the liner with a control valve at
the
skimmer. I put my pump (K6 Sequence) and filter (Fluid Art Bead) in
my
basement for ease of maintenance. I purchased it through Creative
Waterscapes (along with my skimmer and bead filter). Although my
set-up
seems to work great, I built the whole pond without the information
I've
gleaned from this forum. I could have saved a lot of money, and a few
headaches had I known about it!

Mark

"Nedra" wrote in message
hlink.net...
Hi Mark,

What is the size of your drain? 2, 3, or 4 inch? and where did
you buy it?

Nedra
http://www.geocities.com/Heartland/Pines/4836
http://community.webshots.com/user/nedra118

"Mark Mendell" wrote in message
news:wkO4c.7389$wg.3994@okepread01...
If you use a skimmer box, you can plumb the drain right into the
front
of
the box (underneath the skimmer opening) without needing to go "up
and
over."

I have one bottem drain in a 15'x30'x4' and it works great. A lot
will
depend on the contour of the bottom of the pond.

mmendell
"RichToyBox" wrote in message
news:%FN4c.2155$JL2.47891@attbi_s03...
You can have the pipe go up and over, but you need to install a
Tee
and
valve at the top to let air out. Put a backflow preventer
between
the
top
and the bottom drain location to prevent water running back to
the
pond.
Force water in backwards from the pump or settling basin until
all
air
is
out of the top location, and then it will siphon. Periodically,
you
will
need to do the forcing of the water, to evacuate the air, since
some
air
is
in the water and that is the location of the highest vacuum, and
some
air
will separate from the water and accumulate in that location.
--
RichToyBox
http://www.geocities.com/richtoybox/pondintro.html


"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple
questions.
I
would like to add a bottom drain to my pond with having the
plumbming
on
top
of the liner, is this possible? It's to late to redo the pond
and
less
cost
effective. Is there any ideas or suggestions, any help would
be
appreciated.
My pond is currently 12,000 gallons. And i would like an
easier
time
of
cleaning the bottom.

No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

"Mark Mendell" wrote in message
news:YX65c.14384$wg.2789@okepread01...
Priss,

What would I do differently?

As far as the bottom drain goes, not much. How big is your pond? I did a
pretty good job of getting mine in the lowest point, so it does a great
job.
The only mistake I made was when I was installing the liner, after I had
connected the bottom drain, I put a plastic cup into the bottom drain hole
to keep debris out, and told myself "Mark, if you don't remember to take
that cup out of the drain, you're going to be very VERY unhappy." Well,
guess what? Some creative snorkeling was in order.

To drain the pond, I then built a U-shaped bypass line that I install in
my
skimmer (directly connects the bottom drain to the pump). I can drain a
4500 pond in an hour, if I need to.

What else would I have done differently?

I was under the impression that when I filled it with water (estimated
4500
gallons), the liner would conform to the hole. Unfortunately, I ended up
with some folds that were unsightly. So, take care before you fill it!

I got a great deal on limestone, so that's what I used. I spent a very
hot
week in July 2 summers ago moving 20 ton of limestone from my driveway to
my
pond (rented a bobcat), and have spent my time ever since moving it back
out. I'm still trying to get rid of the "ring of rock" look.

In order to cover the unsightly creases and liner, I paniced and began
lining the pond with rock. If I were to do it again, I would take great
care with how my liner was laying before adding water, then add maybe a
few
large rocks. The liner will disappear eventually. The one up side is
that
with all of that limestone in my pond, my ph is very stable!

You're water is going to turn very green. Just be patient, plant lots of
plants, and it will clear. Don't waste your time with chemicals or UV
filters.

What would I NOT do differently?

Many folks on this site use veggie filters exclusively, and that sounds
like
a great way to go (not to mention much more inexpensive that my set-up).
On
the other hand, I can clean my bead filter whenever necessary in 10
minutes
from my basement. It's pretty slick. Depending on the season, I have to
do
it once per week to once every 2 weeks. Flushing it that often, I've seen
no ill effects on the fish.

My pond is outside my back door. I can hear it from my house, and see if
from my kitchen. I see lots of ponders around my area that put their
ponds
in the back of their yards. I love having to walk by and peer into mine
every time I leave the house.

I got the bug from my parents, who have a small pond in Kansas (perhaps 5'
by 10') By the second season, they were wishing it were MUCH bigger. I
decided to build as large a pond as I could manage (to my wife's original
dismay). It's 15' x 30' x 4' deep, with 2 water falls and a smaller
"feeder" pond above. I've yet to wish for more pond, and my family loves
it.

I'll bet that response was more than you bargained for, huh!

Mark


"pmwebdesigns" wrote in message
...
Mark, what would you do different if you had to.
I want two bottom drains on my new pond ( digging next month) and don't
have
a clue what to do.
I went to 3 book stores over the weekend in search of a good pond book.
There were plenty to be found but none had anything on bottom drains!!!!
I was hoping to find something on drains to show me how to set it up and
so
fourth.
Priss


"Mark Mendell" wrote in message
news:t5Z4c.8358$wg.5252@okepread01...
Nedra,

It's a Tetra 3 inch, plumbed through the liner with a control valve at
the
skimmer. I put my pump (K6 Sequence) and filter (Fluid Art Bead) in
my
basement for ease of maintenance. I purchased it through Creative
Waterscapes (along with my skimmer and bead filter). Although my
set-up
seems to work great, I built the whole pond without the information
I've
gleaned from this forum. I could have saved a lot of money, and a few
headaches had I known about it!

Mark

"Nedra" wrote in message
hlink.net...
Hi Mark,

What is the size of your drain? 2, 3, or 4 inch? and where did
you buy it?

Nedra
http://www.geocities.com/Heartland/Pines/4836
http://community.webshots.com/user/nedra118

"Mark Mendell" wrote in message
news:wkO4c.7389$wg.3994@okepread01...
If you use a skimmer box, you can plumb the drain right into the
front
of
the box (underneath the skimmer opening) without needing to go "up
and
over."

I have one bottem drain in a 15'x30'x4' and it works great. A lot
will
depend on the contour of the bottom of the pond.

mmendell
"RichToyBox" wrote in message
news:%FN4c.2155$JL2.47891@attbi_s03...
You can have the pipe go up and over, but you need to install a
Tee
and
valve at the top to let air out. Put a backflow preventer
between
the
top
and the bottom drain location to prevent water running back to
the
pond.
Force water in backwards from the pump or settling basin until
all
air
is
out of the top location, and then it will siphon. Periodically,
you
will
need to do the forcing of the water, to evacuate the air, since
some
air
is
in the water and that is the location of the highest vacuum, and
some
air
will separate from the water and accumulate in that location.
--
RichToyBox
http://www.geocities.com/richtoybox/pondintro.html


"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple
questions.
I
would like to add a bottom drain to my pond with having the
plumbming
on
top
of the liner, is this possible? It's to late to redo the pond
and
less
cost
effective. Is there any ideas or suggestions, any help would
be
appreciated.
My pond is currently 12,000 gallons. And i would like an
easier
time
of
cleaning the bottom.

No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

"Mark Mendell" wrote in message
news:YX65c.14384$wg.2789@okepread01...
Priss,

What would I do differently?

As far as the bottom drain goes, not much. How big is your pond? I did a
pretty good job of getting mine in the lowest point, so it does a great
job.
The only mistake I made was when I was installing the liner, after I had
connected the bottom drain, I put a plastic cup into the bottom drain hole
to keep debris out, and told myself "Mark, if you don't remember to take
that cup out of the drain, you're going to be very VERY unhappy." Well,
guess what? Some creative snorkeling was in order.

To drain the pond, I then built a U-shaped bypass line that I install in
my
skimmer (directly connects the bottom drain to the pump). I can drain a
4500 pond in an hour, if I need to.

What else would I have done differently?

I was under the impression that when I filled it with water (estimated
4500
gallons), the liner would conform to the hole. Unfortunately, I ended up
with some folds that were unsightly. So, take care before you fill it!

I got a great deal on limestone, so that's what I used. I spent a very
hot
week in July 2 summers ago moving 20 ton of limestone from my driveway to
my
pond (rented a bobcat), and have spent my time ever since moving it back
out. I'm still trying to get rid of the "ring of rock" look.

In order to cover the unsightly creases and liner, I paniced and began
lining the pond with rock. If I were to do it again, I would take great
care with how my liner was laying before adding water, then add maybe a
few
large rocks. The liner will disappear eventually. The one up side is
that
with all of that limestone in my pond, my ph is very stable!

You're water is going to turn very green. Just be patient, plant lots of
plants, and it will clear. Don't waste your time with chemicals or UV
filters.

What would I NOT do differently?

Many folks on this site use veggie filters exclusively, and that sounds
like
a great way to go (not to mention much more inexpensive that my set-up).
On
the other hand, I can clean my bead filter whenever necessary in 10
minutes
from my basement. It's pretty slick. Depending on the season, I have to
do
it once per week to once every 2 weeks. Flushing it that often, I've seen
no ill effects on the fish.

My pond is outside my back door. I can hear it from my house, and see if
from my kitchen. I see lots of ponders around my area that put their
ponds
in the back of their yards. I love having to walk by and peer into mine
every time I leave the house.

I got the bug from my parents, who have a small pond in Kansas (perhaps 5'
by 10') By the second season, they were wishing it were MUCH bigger. I
decided to build as large a pond as I could manage (to my wife's original
dismay). It's 15' x 30' x 4' deep, with 2 water falls and a smaller
"feeder" pond above. I've yet to wish for more pond, and my family loves
it.

I'll bet that response was more than you bargained for, huh!

Mark


"pmwebdesigns" wrote in message
...
Mark, what would you do different if you had to.
I want two bottom drains on my new pond ( digging next month) and don't
have
a clue what to do.
I went to 3 book stores over the weekend in search of a good pond book.
There were plenty to be found but none had anything on bottom drains!!!!
I was hoping to find something on drains to show me how to set it up and
so
fourth.
Priss


"Mark Mendell" wrote in message
news:t5Z4c.8358$wg.5252@okepread01...
Nedra,

It's a Tetra 3 inch, plumbed through the liner with a control valve at
the
skimmer. I put my pump (K6 Sequence) and filter (Fluid Art Bead) in
my
basement for ease of maintenance. I purchased it through Creative
Waterscapes (along with my skimmer and bead filter). Although my
set-up
seems to work great, I built the whole pond without the information
I've
gleaned from this forum. I could have saved a lot of money, and a few
headaches had I known about it!

Mark

"Nedra" wrote in message
hlink.net...
Hi Mark,

What is the size of your drain? 2, 3, or 4 inch? and where did
you buy it?

Nedra
http://www.geocities.com/Heartland/Pines/4836
http://community.webshots.com/user/nedra118

"Mark Mendell" wrote in message
news:wkO4c.7389$wg.3994@okepread01...
If you use a skimmer box, you can plumb the drain right into the
front
of
the box (underneath the skimmer opening) without needing to go "up
and
over."

I have one bottem drain in a 15'x30'x4' and it works great. A lot
will
depend on the contour of the bottom of the pond.

mmendell
"RichToyBox" wrote in message
news:%FN4c.2155$JL2.47891@attbi_s03...
You can have the pipe go up and over, but you need to install a
Tee
and
valve at the top to let air out. Put a backflow preventer
between
the
top
and the bottom drain location to prevent water running back to
the
pond.
Force water in backwards from the pump or settling basin until
all
air
is
out of the top location, and then it will siphon. Periodically,
you
will
need to do the forcing of the water, to evacuate the air, since
some
air
is
in the water and that is the location of the highest vacuum, and
some
air
will separate from the water and accumulate in that location.
--
RichToyBox
http://www.geocities.com/richtoybox/pondintro.html


"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple
questions.
I
would like to add a bottom drain to my pond with having the
plumbming
on
top
of the liner, is this possible? It's to late to redo the pond
and
less
cost
effective. Is there any ideas or suggestions, any help would
be
appreciated.
My pond is currently 12,000 gallons. And i would like an
easier
time
of
cleaning the bottom.

pmwebdesigns wrote:
No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

Hi Priss,
My pond is also close to the house. I wanted to enjoy it
year round and I do. I didn't put in a bottom drain at
first but I have added one, using a retro fit drain. This
way I didn't have to cut my liner.
My web site is pitiful right now. I started to work on it
and had to stop because of other work, but it does have a
few photos

--
Bonnie
NJ
http://home.earthlink.net/~maebe43/

pmwebdesigns wrote:
No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

Hi Priss,
My pond is also close to the house. I wanted to enjoy it
year round and I do. I didn't put in a bottom drain at
first but I have added one, using a retro fit drain. This
way I didn't have to cut my liner.
My web site is pitiful right now. I started to work on it
and had to stop because of other work, but it does have a
few photos

--
Bonnie
NJ
http://home.earthlink.net/~maebe43/

pmwebdesigns wrote:
No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

Hi Priss,
My pond is also close to the house. I wanted to enjoy it
year round and I do. I didn't put in a bottom drain at
first but I have added one, using a retro fit drain. This
way I didn't have to cut my liner.
My web site is pitiful right now. I started to work on it
and had to stop because of other work, but it does have a
few photos

--
Bonnie
NJ
http://home.earthlink.net/~maebe43/

pmwebdesigns wrote:
No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

Hi Priss,
My pond is also close to the house. I wanted to enjoy it
year round and I do. I didn't put in a bottom drain at
first but I have added one, using a retro fit drain. This
way I didn't have to cut my liner.
My web site is pitiful right now. I started to work on it
and had to stop because of other work, but it does have a
few photos

--
Bonnie
NJ
http://home.earthlink.net/~maebe43/

pmwebdesigns wrote:
No actually it was great! Thank you very much.
You wouldn't believe some of the smart comments I got from another forum.
The pond I have now is 5x11 3½ ft deep. I'm expanding next month to 15x15
4ft deep.
I want to do this pond right so I don't have to mess with it again except to
clean.
I didn't have a bottom drain on the other. Didn't know anything about one
until someone mention I needed one.
Trying to make everything I can because on a one salary it isn't much.
I just bought Greg's CD http://www.geocities.com/bickal2000/pond.htm
so hopefully I can follow that pretty good. I am not a handywoman. lol
I bought a sequence pump, huge pump. Liner will be on the way next weekend.
I'll have mine in the middle of the yard. It will be close to my back patio.
You got pictures on a website?
Priss

Hi Priss,
My pond is also close to the house. I wanted to enjoy it
year round and I do. I didn't put in a bottom drain at
first but I have added one, using a retro fit drain. This
way I didn't have to cut my liner.
My web site is pitiful right now. I started to work on it
and had to stop because of other work, but it does have a
few photos

--
Bonnie
NJ
http://home.earthlink.net/~maebe43/

According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water from
the bottom. 4" drains are preferred because they will not clog as readily,
and if an inquisitive fish *does* go down the drain, it has room to make it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.

Alternatively, if you're using one of the retro-fit drains that sits on TOP
of the liner instead of through it, it will be powered by a pump, so a 2"
drain can be used. Pumps do better at pushing water than pulling it, but it
"can" do the job. The downside is that a pump will macerate (grind up) the
poo instead of drawing it out in larger pieces, which will make cleaning the
debris from the water column a bit more complicated. However, you have to do
what you have to do. *Any* is better than none.

Lee

"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple questions. I
would like to add a bottom drain to my pond with having the plumbming on
top
of the liner, is this possible? It's to late to redo the pond and less
cost
effective. Is there any ideas or suggestions, any help would be
appreciated.
My pond is currently 12,000 gallons. And i would like an easier time of
cleaning the bottom.

According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water from
the bottom. 4" drains are preferred because they will not clog as readily,
and if an inquisitive fish *does* go down the drain, it has room to make it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.

Alternatively, if you're using one of the retro-fit drains that sits on TOP
of the liner instead of through it, it will be powered by a pump, so a 2"
drain can be used. Pumps do better at pushing water than pulling it, but it
"can" do the job. The downside is that a pump will macerate (grind up) the
poo instead of drawing it out in larger pieces, which will make cleaning the
debris from the water column a bit more complicated. However, you have to do
what you have to do. *Any* is better than none.

Lee

"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple questions. I
would like to add a bottom drain to my pond with having the plumbming on
top
of the liner, is this possible? It's to late to redo the pond and less
cost
effective. Is there any ideas or suggestions, any help would be
appreciated.
My pond is currently 12,000 gallons. And i would like an easier time of
cleaning the bottom.

According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water from
the bottom. 4" drains are preferred because they will not clog as readily,
and if an inquisitive fish *does* go down the drain, it has room to make it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.

Alternatively, if you're using one of the retro-fit drains that sits on TOP
of the liner instead of through it, it will be powered by a pump, so a 2"
drain can be used. Pumps do better at pushing water than pulling it, but it
"can" do the job. The downside is that a pump will macerate (grind up) the
poo instead of drawing it out in larger pieces, which will make cleaning the
debris from the water column a bit more complicated. However, you have to do
what you have to do. *Any* is better than none.

Lee

"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple questions. I
would like to add a bottom drain to my pond with having the plumbming on
top
of the liner, is this possible? It's to late to redo the pond and less
cost
effective. Is there any ideas or suggestions, any help would be
appreciated.
My pond is currently 12,000 gallons. And i would like an easier time of
cleaning the bottom.

According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water from
the bottom. 4" drains are preferred because they will not clog as readily,
and if an inquisitive fish *does* go down the drain, it has room to make it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.

Alternatively, if you're using one of the retro-fit drains that sits on TOP
of the liner instead of through it, it will be powered by a pump, so a 2"
drain can be used. Pumps do better at pushing water than pulling it, but it
"can" do the job. The downside is that a pump will macerate (grind up) the
poo instead of drawing it out in larger pieces, which will make cleaning the
debris from the water column a bit more complicated. However, you have to do
what you have to do. *Any* is better than none.

Lee

"Fernando Rivera" wrote in message
...
I would like to know if anyone can help me out with a couple questions. I
would like to add a bottom drain to my pond with having the plumbming on
top
of the liner, is this possible? It's to late to redo the pond and less
cost
effective. Is there any ideas or suggestions, any help would be
appreciated.
My pond is currently 12,000 gallons. And i would like an easier time of
cleaning the bottom.

"Lee B." wrote in message
...
According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the
drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water
from
the bottom. 4" drains are preferred because they will not clog as
readily,
and if an inquisitive fish *does* go down the drain, it has room to make
it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.
snip

My BD is a DIY...although I never put my DIY diffuser on last year. I think
this year, I will be doing some swimming to get that done. Right now, I have
the pump running to see how it works to remove leaf matter. So far, not so
good without the diffuser.


--
BV.
www.iheartmypond.com

"Lee B." wrote in message
...
According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the
drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water
from
the bottom. 4" drains are preferred because they will not clog as
readily,
and if an inquisitive fish *does* go down the drain, it has room to make
it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.
snip

My BD is a DIY...although I never put my DIY diffuser on last year. I think
this year, I will be doing some swimming to get that done. Right now, I have
the pump running to see how it works to remove leaf matter. So far, not so
good without the diffuser.


--
BV.
www.iheartmypond.com

"Lee B." wrote in message
...
According to the "experts" you should have one 4" gravity fed drain every
10'. To work effectively, you should have a 1/2" drop per foot to the
drain.
Don't forget the anti-vortex cover over the drain, or it will merely suck
the water from directly above instead of being forced to draw the water
from
the bottom. 4" drains are preferred because they will not clog as
readily,
and if an inquisitive fish *does* go down the drain, it has room to make
it
to the settling tank on the other end without getting stuck. DIY types can
jerry-rig a bottom drain very easily using toilet bowl flanges (one below
the liner and one above) and terra-cotta "bowl" type planters for the
anti-vortex. If you can get the type of anti-vortex that has an airdome
attached, it will accomplish two things: a) it will aerate your pond for
you, and b) the rising bubbles actually draw the bottom stuff towards the
drain.
snip

My BD is a DIY...although I never put my DIY diffuser on last year. I think
this year, I will be doing some swimming to get that done. Right now, I have
the pump running to see how it works to remove leaf matter. So far, not so
good without the diffuser.


--
BV.
www.iheartmypond.com